GASKET MATERIAL
GENERAL PROPERTIES AND APPLICATION::. Nitrile Rubber is a black synthetic rubber sheeting. Nitrile is used as asteel against oils,fuels and heat applications.
TEMPERATURE RECOMMENDED MAXIMUM 130C
PRESSURE RECOMMENDED 1000KPA
| Tensile strength | 6,7MN/N5 |
| Compression set | 30% |
| Hardness(A) | 60+-5 |
| Elongation at break | 315% |
| Specific Gravity | 1.15 |
| Aged tensile strength | 111.4% of original |
| Aged elongation at break | 66.7% of original |
Available in rolls- 1,2 meters wide or cut to size Thickness range: 1.5mm,3mm,6mm
GENERAL PROPERTIES AND APPLICATION::. Red Neoprene Rubber is a general purpose neoprene sheeting.A good temperature, oil and a wide range of chemical resistance for use as flange gaskets,scraper curtains mats, sleeves and linings
TEMPERATURE RECOMMENDED MAXIMUM 110C
PRESSURE RECOMMENDED 1000KPA
| Tensile strength | 4,6MN/M2 |
| Compression set | 60.8% |
| Hardness(A) | 65+-5 |
| Elongation at break | 565% |
| Specific Gravity | 1.54 |
| Aged tensile strength | 91% of original |
| Aged elongation at break | 88% of original |
Available in rolls- 1,2 meters wide and approximately 10 meters long,or cut to size Thickness range:0.8mm:1.5mm:3mm:4.5mm:6mm:10mm:12.5mm:15mm:20mm.
GENERAL PROPERTIES AND APPLICATION::. Insertion is a fabric reinforced black natural rubber sheet Extensively used for flange gaskets,strips,curtains, mud flaps and mats
TEMPERATURE RECOMMENDED MAXIMUM 80C
PRESSURE RECOMMENDED 1600KPA
| Tensile strength | 3,6MN/M2 |
| Compression set | 40.3% |
| Hardness(A) | 70+-5 |
| Elongation at break | 260% |
| Specific Gravity | 1.44 |
| Aged tensile strength | 98.6% of original |
| Aged elongation at break | 78.8% of original |
Available in rolls- 1,2 meters wide and approximately 10meters long, or cut to size
| Thickness | Lower Limit | Upper limit |
| 1mm | 0.8mm | 1.2mm |
| 1.5mm | 1.2mm | 1.8mm |
| 3mm | 2.6mm | 3.4mm |
| 4.5mm | 4.1mm | 4.9mm |
| 6mm | 5.4mm | 6.6mm |
GENERAL PROPERTIES AND APPLICATION::. CAF 100 is a medium grade compressed asbestos fibre jointing for general use against low-pressure steam, water, alkalis and mild chemicals
TEMPERATURE RECOMMENDED MAXIMUM 400C
PRESSURE RECOMMENDED 40BAR
| Tensile strength | With grain | 45/Nmm2 |
| Across grain | 14N/mm2 | |
| Compressibility | BS 1832 | 32N/mm2 10% |
| ASTM | 35N/mm2 11% | |
| Recovery ASTM | 35N/mm2 40% | |
| Relaxation Stress | BS 1832 | 13N /mm2 |
| DIN52913 | 14N/mm2 | |
| Specification Compliance | French | NFT.48-001 Type A |
| British | BS2815Gr .B | |
| Sheet Size | 1500mm x 2000mm | |
| Thickness Range | 0.4mm 0.8mm 1mm 1.5mm 2mm 3mm |
GENERAL PROPERTIES AND APPLICATION::. Wire reinforced CAF 400 for arduous applications involving fluctuating temperatures and pressures
COLOUR BLACK AND GRAPHITED BOTH SIDES
STD COMPLANCE DIN3754 IT 400 WIRE REINFORCED
TEMPRETURE RECOMMENDED MAXIMUM 540C
PRESSURE RECOMMENDED MAXIMUM
| Minimum Tensile Across Grain DIN52910 | Not applicable |
| Density | - |
| Resilience ASTM F36A | 8% CY Average 45%CY Minimum |
| Typical max %swell properties water ASTM oil #3 | DIN 3754 10% |
| Residual stress Din52913 | >30N/mm2 |
| PRODUCTS| PROJECTS| TECH SPECS| PROFILE| MANUFAC| CONTACT US